LED strip for ceiling lighting is a unique element of interior design. Such illumination was almost the first tool that helps to give volume to even the smallest room, and at the same time to give visual lightness to modern suspended structures.
LED strip for ceiling lighting. How to choose?
The choice of lighting for any ceiling design today is quite wide. It can be organized with:
- conventional incandescent bulbs;
- fluorescent plafonds;
- neon lamps;
In modern design solutions can be used any of the above products. Using one type of lamp to illuminate the ceiling or a combination of different options allows you to create unique lighting effects. When choosing a ceiling lighting option, you need to carefully consider such moments as:
- service life of the lighting device;
- minimum level of heat released;
- ease of installation and replacement if necessary;
LED strip meets all requirements for lighting. Ceilings with similar illumination are very popular among craftsmen, designers and ordinary citizens. LED strip to illuminate the ceiling is a unique flexible material on which there are tracks responsible for conducting electricity on it. Diodes attached to conductors are light sources.
The main advantage, because of which more and more buyers choose their own choice of illumination, can be called low energy consumption. The ten-meter LED strip uses much less energy to glow than an ordinary incandescent lamp, but the light from the diodes is much brighter. The service life of LEDs is much longer than that of filament lamps. To create a unique interior, the flexibility of a similar product matters. As well as its ability to provide illumination of different brightness and in a variety of colors.
When choosing an LED strip to illuminate the ceiling, you should pay attention to such moments as the density of the diode lamps on the tape, the power consumed by them, and the presence of moisture protection. The color scheme of diode strips is quite different, they can be divided into monochrome and universal. Monochrome can give light only one color. Universal or RGB tapes glow in different colors: red, blue, green. In the RGBW strips, a white backlight is additionally used.
Lighting in the bathroom, photos of various options. Ceilings with one or another type of lighting. Which lamps are best used to create lighting in the bathroom. Safe light.
The cost of the diode strips is about the same, so for arranging interesting interior options it is worth using RGBW. It can be supplied with a special controller that allows you to adjust the color gamut and intensity of the backlight.
Also, such light sources differ in the density of the diodes. This figure varies from 30 to 120 pieces per meter. To illuminate a large area, it is better to use a tape with a high density, and for a directional light emission, a smaller indicator will do. Some designers successfully combine both, if space permits.
No less important parameter can be called power consumption. The brightness of the LED itself depends on this figure. The most famous models are SMD 5050 and SMD 3528. The power of the first with a density of 60 pcs / m is 4.8 W / m, and the second with the same density of 14.4 W / m. On which of the options it is worth stopping your choice, you need to decide on your own, depending on the goals and tasks that the backlight will perform.
Often, LED strip to illuminate the ceiling used in bathrooms. For such premises suitable strip protected from moisture. There are also moisture resistant options that can be mounted directly in the water. The degree of protection depends on the cost of such products.
Helpful advice! If the final power of the backlight turned out to be quite large – you can buy several small power supplies instead of one large one.
LED strips for illuminating ceilings can be placed in various places of suspended structures. Consider the most common ones.
With this arrangement, the suspended structure of a multi-level ceiling seems light and literally floating in the air. The niche is specially equipped for lighting. Depending on the placement of the tape inside such a “pocket”, you can get different lighting effects. If the LEDs are pointing up, you can get a soft diffused light. When designing a diode strip on the side of a niche, the light will turn out to be directional and will gently slide along the “soaring ceiling”.
A similar variant of the backlight is used only in conjunction with the half-transparent stretch ceilings. Tapes are located directly in the gap between the material and the main ceiling. This arrangement gives the room a soft, diffused light and creates the feeling of the ceiling glowing from the inside.
More interesting are the options for lighting, which are combined with a delicate pattern made on the material of the tension structure. With the help of such an original tandem you can get either an imitation of a real solar glow or a starry night sky. No less interesting are the patterns made by LED strips inside the tension structures.
Helpful advice! When creating a flashing ceiling light, you cannot use such frequencies: 0.5, 2, 7 Hz per second. They coincide with the rhythms of the brain and can even provoke an epileptic seizure.
This way of creating decorative lighting is quite simple and easy. For its arrangement does not require suspension or tension structures. For these purposes, use the usual eaves with a width that allows you to place behind him the LED tape. The fastening of such an interior element is made to the wall either with adhesive solution or with the use of fasteners. The tape is glued directly to the edge of the eaves.
Any LED strip is equipped with a special adhesive layer that allows you to easily attach it to various surfaces. Before mounting the light strip, the surface is thoroughly cleaned from dust, dirt and debris. Such a measure will allow the backlight to last much longer.
Sold diode strips in special coils of 5 meters. If shorter length is needed, then you can simply take the scissors and cut off the excess. This should be done only at the designated cut point. For soldering tapes and attaching wires to them, you need to use a low-power soldering iron.
Helpful advice! If you plan to install light elements yourself, it is worth remembering that you can not connect 3 five-meter tape in series. It is better to separate the wires from each element to the controller.
The power supply of the diode strips is carried out using a step-down power supply unit of 12 or 24 V. It should be purchased additionally or immediately buy ready-made kits, including a reel with diodes, a remote control and a power supply unit.