Plank face for metal: purpose and installation procedure

Roofing is one of the basic elements of any building. It depends not only protection from precipitation, but also the appearance of the house. Modern roofing materials allow you to create practical and beautiful roofs of houses, spending a minimum of resources. One of such materials is metal tile. It is quite convenient to install, but requires the use of additional elements, among which the face plate for metal tiles.

Plank face for metal: purpose and installation procedure

End plate for metal tile: the purpose and features of installation

In order to cover the roof with metal roofing material it is necessary to use several types of slats:

  • eaves;
  • face or wind;
  • ridge;
  • contiguity plank for metal tile.

All of them serve as additional protection of wooden elements of the roof from the effects of adverse environmental factors, as well as for decorative purposes.

Plank face for metal: purpose and installation procedure

The level face for a metal tile is made of galvanized metal, up to 0,55 mm thick. It comes in various colors, similar to the main roofing material. There are products with a polymer and composite coating. This element of the roof has the form of a corner in cross section. Its edges are slightly curved or there may be ribs on the plane. These nuances give additional rigidity to the product. The standard length of the strap is 2 m. Its fastening is carried out on the ends of the slopes, which ensures protection of the batten from moisture and wind penetration. For this reason, this product is also called a wind strip for metal tiles.

Plank face for metal: purpose and installation procedureTechnology roofing of metal. Description of the technology of mounting metal roofing. Features of mounting metal on a complex roof

  1. The length of the end of the slope is measured and the number of whole slats is calculated. If necessary, the latter is cut to the desired length.
  2. Installation begins at the bottom of the ramp and goes up. In this case, the products are overlapped with at least 50 mm.
  3. The horizontal part of the end plate for metal should completely overlap the crest of the roof covering, and the vertical part should close the battens from their ends.
  4. Fixing of an element is carried out with the help of roofing screws of the same color, both in the vertical plane and in the horizontal one. At the same time, the screws are screwed from above strictly into the ridge of the metal tile. The distance between the screws should be 30 – 50 cm, and screw them most conveniently with a screwdriver, starting from one side so that the bar does not jarred.

Plank face for metal: purpose and installation procedure

Do not forget about sealing the gaps between the bar and the roof covering. In addition to the protective function, the wind strip for metal tiles also carries a decorative one. The roof, decorated with this element, has a more complete and harmonious appearance.

Helpful advice! When fixing the strap with self-tapping screws, it is necessary to be very careful and not to miss the edge on the batten. If this happens, then in no case can the screw be removed, since it closes the hole made.

Plank face for metal: purpose and installation procedure

In the process of carrying out roofing work, great attention should be paid to safety. Stairs or scaffolding must be securely fastened and not dangerous. It is most convenient to mount the wind strip for metal tiles from scaffolding installed along the building gable. This will allow to move freely along the entire length of the slope. Before fastening the additional element, it is worth stitching the lower part of the batten, hanging over the pediment, with facing material. This will allow you to avoid inconveniences in the future, as the installed bar can interfere with this process.

Plank face for metal: purpose and installation procedure

When installing the product pay attention to the alignment of both planes, as the “waves” or “torsion” will not only reduce the protective function of the element, but also spoil the entire appearance of the roof. Even fastening can be ensured only if you strictly follow the rules of installation and use of measuring tools.

Helpful advice! The end plate for metal should be fastened with self-tapping screws with rubber washers. This will not allow water to get under it, and loosen the wind, causing later rattling sounds.

Plank face for metal: purpose and installation procedure

Among other elements required for the installation of the roof, you can select the ridge bar that closes the ridge on top of the coating sheets. The curtain rail is similar to the end, but is mounted on the eaves before mounting the roof. Of particular interest is the junction bar for metal tiles, which is used at the joints of roofing sheets with walls, pipes, valleys or other roof elements. It is installed on top of the metal tile and does not allow water to get in through the junction.

Plank face for metal: purpose and installation procedure

In conclusion, you can add that the need for additional elements must be calculated when purchasing the material in order to select all of them of the same color with metal tile.

Like this post? Please share to your friends:
//graizoah.com/afu.php?zoneid=2466924