Water procedures in the open air are very useful, therefore many adherents of relaxation and quenching decide to make a summer shower for the shower in the country with their own hands or at least install a ready-made booth on the site. This article will help to understand the design features, correctly choose the dimensions and installation site, draw up a preliminary scheme and complete all construction stages without errors.
Summer shower for the shower in the country with their own hands: the choice of design and design
Building a street shower is sometimes the only way to fully wash yourself after a busy day spent in the garden, or to cool off in the summer heat. This small structure has many variants of execution, and both from the technical side and with regard to aesthetics. However, all designs have a similar device.
Standard suburban shower consists of the following elements:
- frame part;
- water tanks;
- fences (walls);
- pallet (floor).
On the Internet you can find a lot of interesting photos, the souls depicted in them, have a diverse architecture. And there are not only traditional, but also rather unusual and original versions of the design.
There are several options for assembling the structure:
- the simplest buildings that do not have solid side walls;
- lightweight constructions with improvised fencing;
- capital-type shower cabins, in which the walls are made of polycarbonate and other materials.
In addition, there are closed and open cabins, as well as semi-closed structures. There are options with two partitions: in one area there is a plumbing, and the other is designed for storing bath accessories, towels and clothes.
According to the method of water supply country souls are of two types:
- Plumbing – a centralized water supply system is supplied to the booth.
- Capacitive – at the top is the installation of a tank for a summer shower with water, which is heated under the influence of sunlight. For these purposes can be used tanks or barrels.
Note! The installation position of the shower depends on how the water is supplied. If the proposed construction site is in close proximity to the house, it is desirable to bring not only a centralized water supply system, but also to organize a sewage system for the discharge of wastewater.
The design of the simplest garden shower includes just one bathing cabin, so no need to develop a complex drawing for construction. Most often, the souls depicted in the photo in the country with their own hands have the standard dimensions – 1x1x2.2 m. These figures correspond to the lower limit, the construction of a smaller booth is unacceptable. Approximately 0.1 m of height is allocated for the arrangement of the pallet, about 0.15 m is required for the watering can hanging from the ceiling.
It is also not recommended to significantly exceed the permissible height parameters. Otherwise, the process of filling the tank with water will become more complicated, and it will be difficult for a person with small stature to reach the crane, which is installed in front of the watering can.
The depth and width of the shower for giving is selected individually. However, it is still not necessary to cut the dimensions of the structure smaller than the standard size, otherwise it will be very close inside. If the constitution of the owners of the soul is large enough, then the width and depth of the stall is chosen so that people can swim comfortably.
If budgetary opportunities allow, and there is also a desire to work out the construction scheme more thoroughly, additional convenience can be added. In the presence of lighting at night to use the shower will be much more convenient. For these purposes, any type of lantern with a low power level will do. The main thing is that it contains the necessary level of moisture protection. In the daytime there will be enough natural light. To do this, you can cut a small window at the top of the door or on any of the side walls.
Helpful advice! To exclude the likelihood of drafts, the window in the shower stall is desirable to glaze.
It is recommended as a tank for a summer shower to buy a square-shaped tank. Installing it in the upper part of the booth, you can save on the purchase of roofing material, which in this case is not required.
You should not create a completely sealed design. In such conditions, steam will accumulate inside the booth, which will make it difficult to breathe. To avoid such effects, you can install a small vent on the back or side wall. Since hot air is much lighter than cold air, installation of the hatch is carried out in the upper area of the cabin.
If the structure will be operated in the cool time of the day, experts advise to buy for the summer residence a heated shower. To equip a similar design independently, it is enough to install the tank equipped with the built-in TENG. A heating element that functions at the expense of electricity will provide hot water at any time.
A dressing room will be a useful addition to the shower. It can be located inside the booth or outside. In the first case, you will have to increase the dimensions of the house. It is enough to separate the storage space for clothes using a film screen.
To organize a comfortable locker room, you can use a dressing room. Its construction is constructed separately and installed so that one of the walls adjoins the shower. To do this, place additional racks, after which the frame is sheathed with any sheet-type material. For more comfort inside you can put benches and a compact table.
Before you make a shower in the country with your own hands, you need to make sure that the diagram reflects even the smallest elements, right down to the shelves, hooks for clothes and mirrors. If the design of the booth is designed for several people, then the drawings must contain a sewage system, as well as the point of placement of the drain hole.
After all the nuances of the design have been thought through and the drawing has been drawn up, it is necessary to choose the optimal place for the installation of a shower. It is desirable that the construction area is located at a distance from buildings and tall trees. For a shower in a country house with heating, this nuance is not particularly important, but if the water in the tank is heated in a natural way, the place where the cabin is located must be sunny.
Important! You can not put the shower in the area located in a low place. Such placement will negatively affect the further operation of the booth, since the water flow will be impeded.
There are several options for arranging the stock system. If infrequent use of the shower is expected or the amount of water consumed will be small, it is possible to limit the formation of a drainage layer, which is located at the bottom of the pan. If the cabin is designed to service a large number of people, a septic tank will be required. In this case, it is not recommended to settle the waste pit directly under the shower, otherwise it will not be possible to avoid the appearance of unpleasant odors. To do this, it is enough to install a septic tank at a distance of 2-3 m from the building.
Most often, showers have a small weight, but the design is weighted by the presence of a tank filled with water, which is installed on the roof. To keep the house stable, a solid foundation is formed under it. One of the most common basement options is a monolithic slab. Concrete is used for its construction.
The procedure for the construction of slab foundation for a garden shower do it yourself:
- In accordance with the dimensions of the shower stall, a hole with a depth of not more than 0.5 m is dug out at the site.
- A formwork structure is installed along the perimeter of the recess.
- At the bottom of the formed sand and gravel pillow thickness of 0.2 m.
- The reinforcing mesh is being installed.
- The formwork is filled with cement mortar. This is done so that the slab of the future base rises above the ground level by 0.1 m.
Red brick can be used for the construction of the formwork. Before filling with cement mortar, it is imperative to lay a sewer pipe to drain the sewage. It is necessary to make this procedure at this stage, since it will be impossible to implement it later.
When building a wooden shower for giving, it is recommended to use the foundation on piles. To do this, using a drill, you need to make holes around the perimeter of the structure, the depth of which is 1 m. Inside they are placed pipes. It can be metal or asbestos products. They should be pre-cut so that, after installation, they would rise above ground level by about 0.2 m.
Important! Be sure to make sure that all pipes are installed strictly in an upright position. Only then can you fill the cement mortar.
Filling is carried out both from the outside of the pipes and inside them. First you need to do the installation of anchor studs. After hardening of the concrete, the frame of the lower strap for the booth is formed. For these purposes can be used wooden beam. It drilled holes for mounting studs. Then with the help of nuts, the frame is tightly attached to the base piles.
As the basis for the construction of the shower can be used column type of the foundation. Its design is very similar to the pile option. The only difference is in the technology of manufacturing supports. It is necessary to dig holes in the corners of the booth with a size of 0.2×0.2×0.5 m. If you wish to manufacture or buy a summer shower for giving with a changing room and with a tray, you will have to increase the number of holes to 6 pieces. Additional recesses are located in the central part of the long walls.
The walls of the formed depressions need to cover with roofing material. After that, the anchor studs are mounted in the center. For pouring cement mortar will need to make a formwork design. At the final stage, it will be necessary to attach the frame of the lower strap of the booth to the studs.
Related article:
Construction of a toilet in the country with their own hands, drawings, sizes
Types of autonomous toilets. Choosing a place for the construction of a toilet at the dacha
If it is planned to build a capital shower for brick-house dacha, it is advisable to use a tape type of foundation. A trench is being formed along the perimeter of the future construction. The optimum depth is 0.5 m. Further, the installation of the formwork is carried out. At the bottom of the trench, it is necessary to form a sandy-rubble pillow with a thickness of 0.1 m. After that, the fittings are laid and concrete is poured. This should be done in such a way that, when finished, the foundation towers above the ground level by about 0.1 m.
When the base completely hardens and dries, it will be possible to proceed to the construction of the sewer system.
There are several ways to organize the waste system in the shower. The choice of construction technology depends on several factors:
- the type of soil on the site;
- type of foundation;
- the number of people living in the house.
If a monolithic slab is used as a foundation for a summer shower in the country, then before performing the pouring it is necessary to lay a system of plastic pipes with a knee. The plate is formed in such a way that from all sides there is a bias towards the drain hole. The sewer pipe is brought out of the shower and connected to the general system of drains. You can bring drainage to the drainage well.
Helpful advice! For the construction of a similar sewage system for a booth installed on a foundation of another type, it is not necessary to fill floors with concrete. It is enough to buy a summer shower to give with a tray made of acrylic. This element will function as a floor.
A shower stall with connection to the sewer system is the best option for a large family, because the pit will not be able to accommodate the amount of waste that will be formed during operation. If the design is designed for 1-2 people, it will be enough to drain directly under the booth. But this type of system is suitable for areas with loose soil type, when the shower is installed on a columnar or pile foundation. This option can be used on a tape basis.
First you need to remove the layer of soil with a depth of 0.5 m. The hollow formed at half its height is filled with gravel or stone. The remaining part is filled with rubble with a small fraction. After the design of the booth is assembled, a pallet made in the form of a wooden lattice is installed on a layer of rubble. The system is designed in such a way that the wastewater passes through the drainage layers and is gradually absorbed into the soil.
Sometimes the owners of the dachas bring the sewer into the garden, which is not a good solution. If, nevertheless, to resort to a similar method, it is desirable that the place where the water is drained is well heated by the sun. Otherwise, the liquid will accumulate, and around the shower a swamp teeming with mosquitoes forms.
For the construction of a booth for a homemade shower can be used any materials at hand.
For these purposes, suitable:
- wood;
- polycarbonate;
- professional flooring;
- brick.
Each type of material has its own advantages, features and properties.
There is a little trick to help you save money when building a shower hut. To reduce costs, it is enough to use one of the blank walls of the building as a side for the booth.
Before building a low-cost summer shower, it is necessary to fix a small-sized water tank equipped with a watering can on the wall. Here you can also install related elements of comfort, for example, coat hooks, shelves, etc. At the top of the future structure is a partition. It is fixed on the wall of the building. A tarpaulin or a film (necessarily opaque) can be used as an entrance door. The shutter is suspended using rings.
The floor is arranged so that drains are diverted as far as possible from the foundation part of the house. To do this, the site is concreted, or you can do with the installation of an acrylic pallet.
Helpful advice! If you use the internal corner of the structure, which has an L-shaped, you can generally avoid the construction of the sides of the cabin. Their function will be performed by the walls of the building.
The most common version of the dacha shower is a booth made in the form of a wooden house. This type of building is considered one of the most affordable. Wood is easy to process. At the same time, it perfectly retains heat, which is an undoubted advantage if the shower will be used in cold weather.
For the construction of a summer shower in a private house with your own hands, it is desirable to use a wooden beam. For the manufacture of corner racks of the booth, a material having a section size of 10×10 cm is required. A tank designed for 200 liters of water is installed in the upper part of the shower, therefore the timber must be thick enough to withstand a similar weight load.
To hang the door you will need to install two additional racks in the front of the booth. These elements are placed between the corner posts. For their manufacture, you can take a bar with a section size of 5×5 cm.
In order to form a small inclination angle for a single-pitch cabin roof, it is recommended to install front corner posts 0.2 m higher than the rear ones. This is not required if a square-shaped tank is used as the tank. In this case, the racks are mounted on the same level.
All supports are attached to the wooden frame bottom trim. For fixing it is necessary to use hardware and metal corners. In the upper part of the construction is strapping in a similar way. To strengthen the rack, you can use spacers. On the top trim of the frame part of the booth is formed the basis for mounting the tank. At the same time it is necessary to read not only the size, but also the shape of the tank.
For covering the frame part of the building, you can use a board 2 cm thick. Such material is also suitable for the manufacture of a door. It is necessary to lay the boards in one row and knock them together with the help of two jumpers. To prevent the door from tilting, the structure can be strengthened obliquely, using a long rail. The door box for the summer dacha shower is made of boards, the thickness of which is 4 cm. It is recommended to use self-tapping screws as fasteners.
When the cabin is fully prepared, it can be opened with a colored varnish compound. On the inside, the entrance is curled with foil, otherwise the doors will swell from moisture.
Helpful advice! Often used for the construction of a large barrel for the shower to the country. Having established a watering can over a design, it is possible to receive the budgetary version of a wooden cabin.
Since wood is subject to deformational changes under the influence of moisture, many landowners are thinking about how to make a shower in the country with their own hands from more practical and resistant materials, such as polycarbonate. The frame part of the booth is made in the same way as in the case of wooden shower, but as a material, you must use a metal profile. The optimal size of the cross section is 4×6 cm.
The frame part of the booth is formed using racks and jumpers between them. In this case, metal elements are used, therefore a welding machine is required for their fastening. Moreover, the assembly order can be performed in several ways. In the first case, the frame part is welded separately, after which it is installed on the base and fixed by means of anchor bolts. The second method involves concreting the racks during the pouring of the foundation. Then the binding is formed, the struts are attached.
It is desirable to use sheet material 1 cm thick as a polycarbonate shower casing. It is fastened to the metal frame with the help of hardware, which must necessarily have sealing gaskets.
At the last stage of the construction of the shower tank is installed. Capacity can be made independently using any container made of stainless steel or plastic. To do this, it is necessary to form a hole in the bottom, the diameter of which is 1.5 cm. A section of pipe with threads on both sides is attached to it with the help of nuts. The length of this element should be 30 cm.
In the roof of the booth in the center you want to make a hole where the socket will be inserted. After the tank is installed on the free end, a tap and a plastic watering can are screwed on. Then the container is firmly fixed on the frame of the frame part of the booth, filled with water and covered with a lid.
To create a heated summer shower, it’s enough to install a heating element in the tank. Of course, the natural energy of the sun can be used to heat the water. In this case, the cost of electricity will be absent. However, the sun’s rays are not able to heat a large volume of fluid. In addition, not every region has the necessary climatic conditions.
The network can find a lot of schemes needed to connect a summer shower to give heated to electricity. The advantage of these devices is that the water warms up in the tank quickly enough regardless of the time of day and the weather outside. In this case, the person can set the temperature mode himself. If you attach a piece of foam to the hose, the warmest water will flow into the watering can. For the same reason, fluid intake is carried out from the upper zone of the tank.
Helpful advice! To speed up the process of heating a fluid, you can add a coil to the circuit.
To simplify the construction technology, you can buy a summer shower in finished form and install it on a prepared base. The cost of booths is varied and it depends on various factors.
The price of products is influenced by the following points:
- production material;
- modification (presence of changing rooms);
- water tank form (in the form of a barrel, square tank);
- equipment (the presence of a heating element, tank, temperature sensor, etc.);
- tank capacity;
- material of which the water tank is made.
Average prices for finished structures
| Name | price, rub. |
| Metal frame and PVC fabric | |
| Garden shower | 7700 |
| Garden shower with water heater | 8900 |
| Garden shower with water heater and locker room | 12,900 |
| Polycarbonate construction | |
| Cab | 11600 |
| Cabin with 130 l tank | 14800 |
| Cabin with 200 liter tank | 15300 |
| Cabin with a tank of 130 liters with heating | 16800 |
A large variety of materials suitable for construction, as well as manufacturing techniques allows any summer resident to acquire a comfortable and convenient shower in the country. Moreover, you can make a booth yourself from improvised means or buy it in finished form in a specialized store.
