The device of gate for the private house. Photo of possible options

High-quality, properly selected gate, not only a question of housing security, but also the appearance of a private house. They are an integral part of the site and should easily fit into the overall design, as well as be in harmony with other buildings. The modern market offers the consumer a variety of options from various materials, with the most modern control systems and without them. These are mainly reliable, durable, attractive in appearance door models for a private house. Photos showing all the positive qualities of such structures are presented below.

The device of gate for the private house. Photo of possible options

Types of gates for a private house. Photo samples

Gates are divided into several types depending on the material of manufacture and options for opening / closing. They are:

  • swing;
  • sliding;
  • lifting.

The device of gate for the private house. Photo of possible options

Recently, the most common options have become metal structures. For a cheaper arrangement, you can use the usual profiled, and for a richer and more luxurious – a combination of solid metal with elements of forging. However, the gates of wood also look pretty good.

The device of gate for the private house. Photo of possible options

This is the most common type of gate for a private house. Their arrangement is possible in the presence of free space, allowing you to open the doors without problems. Modern swinging structures are a metal frame, which is subsequently lined with metal, corrugated board, wood or special sandwich panels.

The device of gate for the private house. Photo of possible options

The profile pipe 100×100 is perfect for the support. For their installation, wells are dug, which are filled with rubble and sand, creating a so-called pillow. The support fixed in such a pit with spacers is poured with concrete with the addition of coarse gravel.

Important! For complex, clay soils, such a pillar arrangement may not be sufficient. In such situations, an additional jumper is welded between the supports at a depth of about 40 cm.

The device of gate for the private house. Photo of possible options

For the frame of the frame using a pipe 60×30. For a rigid cross member, which is welded inside the finished frame, the metal profile is taken in a smaller section, approximately 40×20. Along the edges of the frame, hinges are welded, as well as the arms for the lock and bolt. Upon completion of the assembly, the welds must be grinded with a grinder, and then primer and paint should be applied.

The device of gate for the private house. Photo of possible options

If profiled sheeting is used for plating, then the C8 or C10 brands are best suited. The most convenient for cutting profile sheets to use the grinder. Special disks without abrasive spraying are put on it. Fastening, cut to size, corrugated is riveted with a riveting tool, fastening with screws is also allowed.

Important! Laying profiled sheeting should be overlapped, capturing 1 wave of the neighboring element.

The device of gate for the private house. Photo of possible options

Not in all situations installation of oar entrance groups is possible. When there is very little space for opening the valves, they use a sliding type of construction. Mostly sliding systems consist of one leaf, which is made on the same principle as the usual swing gates for a private house. Photos of such samples demonstrate the convenience of their operation.

The device of gate for the private house. Photo of possible options

In order for the construction to move, special rails are equipped, and rollers are welded at the bottom of the sash. It is also necessary to weld a guide to the upper part, which is intended for fixing the sash in a certain position.

The device of gate for the private house. Photo of possible options

Operation of the rail gate is difficult in the winter, as the moving parts may become clogged with snow or ice. During snowfall requires thorough cleaning of these elements, as well as the area around. Also along the sash gate you can lay a heating cable that will melt the snow, restricting movement.

Not everyone likes to open and close sash manually. For this you have to get out of the car, then sit down again, it takes a few minutes of precious time. It is much more convenient to press a button and the “casket” will open itself.

The device of gate for the private house. Photo of possible options

You can automate swing and sliding gates. For this purpose, specialists have developed special linear and lever electric drives that allow the doors to open independently. Other systems consist of an electric motor, a toothed rack, through which the gears transmit force to the door leaves.

The drive itself is mounted on rails. Limit switches are installed on the rack, and photocells on the posts. Convenient remote allows you to quickly and easily open the gate directly from the car without physical effort.

Like this post? Please share to your friends: